Search Results

Search found 12980 results on 520 pages for '11 04'.

Page 442/520 | < Previous Page | 438 439 440 441 442 443 444 445 446 447 448 449  | Next Page >

• Can this USB3 behaviour be anything else than a hardware failure?

  - by Jonas Wielicki

  While my motherboard is half a year old now (ASUS M5A99X EVO), I only recently made use of the USB3 boards (after purchase of USB3 external harddrive). However, I am encountering issues. I am running linux 3.6.7-4.fc16.x86_64. Initially, the harddrive worked fine with USB3 (amazing ˜160MB/s), but I had some problems after putting after putting the harddrive to sleep manually after use (backup) with hdparm -Y. After some time, the device disappears from lsusb and i see the following in dmesg: [ 1924.091107] xhci_hcd 0000:05:00.0: xHCI host not responding to stop endpoint command. [ 1924.091114] xhci_hcd 0000:05:00.0: Assuming host is dying, halting host. [ 1924.091147] xhci_hcd 0000:05:00.0: HC died; cleaning up [ 1924.091233] usb 11-1: USB disconnect, device number 2 [ 1924.091272] sd 6:0:0:0: Device offlined - not ready after error recovery Testing with my (USB3 capable) notebook, I could not immediately reproduce the behaivour. I put the drive to sleep with hdparm -Y and waited for like an hour, but it was still listed in lsusb and responded after a few seconds delay when I tried after the hour of waiting. After an hour, on the desktop, the device would've usually vanished. Googling for this issue, I came across hints that playing around with IOMMU settings and upgrading the BIOS might help. I upgraded the BIOS and tried both with and without IOMMU enabled, got similar results. Most disturbing is, that one of the two USB 3.0 hubs sometimes also disappears from lsusb (or does not show up after boot at all). I've also heard that there are some hardware issues with ASUS USB3 ports. Applying mechanic force to the capble doesn't push the issue to one side or the other. Also, udev seems to reenumerate all devices if I plug the HDD into the USB 3.0 port without success (I can notice from my keyboard layout being changed to the default, which I do not use normally). The drive is externally powered and the external power supply is plugged in (it also stays powered when unplugging from USB, although it will spin down then). So before I try to return the board, I wanted to find out whether this can be anything else than a failure on the motherboard?

  Read the article

• PHP-FPM performing worse than mod_php

  - by lordstyx

  Recently the website I maintain has been growing a lot and I saw the point coming where I'd want to switch from apache to nginx, because I kept on reading that it performs way better. Now I've done the switch, and I have to say, nginx is keeping up just fine. However, php-fpm is forming a problem. Where the php pages used to take 0.1 second to generate with the same load they now take around 3 seconds! Furthermore the error.log from nginx is being spammed with errors like: upstream timed out (110: Connection timed out) while connecting to upstream, client: ... I also tried using unix sockets instead, but those would complain about the following: connect() to unix:/tmp/php5-fpm.sock failed (11: Resource temporarily unavailable) while connecting to upstream I've fiddled with settings here and there but nothing seems to work. Changing the amount of pm.max_children doesn't seem to help a lot either, but with it's current amount at 350 it seems to be the lesser of all evil. The server that's being used has 3 GB RAM (not all of it is free due to a MySQL server also running) along with 2 dual-core processors (4 cores in total). Am I doing something majorly wrong with the settings here, or is the server simply not capable enough? EDIT: Here is the nginx server block server { listen 80; listen [::]:80 default ipv6only=on; root /var/www; index index.php index.html index.htm; server_name localhost; location / { try_files $uri $uri/ /index.html; } location /doc/ { alias /usr/share/doc/; autoindex on; allow 127.0.0.1; deny all; } location = /50x.html { root /usr/share/nginx/www; } location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(/.+)$; # NOTE: You should have "cgi.fix_pathinfo = 0;" in php.ini try_files $uri = 404; # With php5-cgi alone: fastcgi_pass 127.0.0.1:9000; # With php5-fpm: #fastcgi_pass unix:/tmp/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; } location ~ /\.ht { deny all; } } And the php-fpm pool: [www] user = www-data group = www-data listen = 127.0.0.1:9000 ;listen = /tmp/php5-fpm.sock listen.backlog = -1 pm = dynamic pm.max_children = 350 pm.start_servers = 200 pm.min_spare_servers = 10 pm.max_spare_servers = 350 pm.max_requests = 1536 rlimit_files = 65536 rlimit_core = unlimited chdir = /

  Read the article

• page up/down print ~ instead of history search in terminal

  - by Desmond

  I am on a Macbook Pro with mac os x 10.8.2 I have set: page up: \033[5~ page down: \033[6~ in terminal keyboard settings (pressing esc to get \033). My ~/.xinputrc is: # Be 8 bit clean. set input-meta on set output-meta on set convert-meta off # Auto completion options set show-all-if-ambiguous on set completion-ignore-case on # Keybindings "\e[1~": beginning-of-line # Home key "\e[4~": end-of-line # End key "\e[5~": history-search-backward # Page Up "\e[6~": history-search-forward # Page Down "\e[3~": delete-char # Delete key "\e[5C": forward-word # Ctrl+right "\e[5D": backward-word # Ctrl+left I am just following a guide found on internet (actually there are a lot of guide really similar): http://macimproved.wordpress.com/2010/01/04/fix-page-updown-home-end-in-terminal/ Unfortunately, the only (terrific) result is that when I press page up (fn + up arrow) just a "~" is printed in the terminal.

  Read the article

• APC PHP cache size does not exceed 32MB, even though settings allow for more

  - by hardy101

  I am setting up APC (v 3.1.9) on a high-traffic WordPress installation on CentOS 6.0 64 bit. I have figured out many of the quirks with APC, but something is still not quite right. No matter what settings I change, APC never actually caches more than 32MB. I'm trying to bump it up to 256 MB. 32MB is a default amount for apc.shm_size, so I am wondering if it's stuck there somehow. I have run the following echo '2147483648' > /proc/sys/kernel/shmmax to increase my system's shared memory to 2G (half of my 4G box). Then ran ipcs -lm which returns ------ Shared Memory Limits -------- max number of segments = 4096 max seg size (kbytes) = 2097152 max total shared memory (kbytes) = 8388608 min seg size (bytes) = 1 Also made a change in /etc/sysctl.conf then ran sysctl -p to make the settings stick on the server. Rebooted, too, for good measure. In my APC settings, I have mmap enabled (which happens by default in recent versions of APC). php.ini looks like: apc.stat=0 apc.shm_size="256M" apc.max_file_size="10M" apc.mmap_file_mask="/tmp/apc.XXXXXX" apc.ttl="7200" I am aware that mmap mode will ignore references to apc.shm_segments, so I have left it out with default 1. phpinfo() indicates the following about APC: Version 3.1.9 APC Debugging Disabled MMAP Support Enabled MMAP File Mask /tmp/apc.bPS7rB Locking type pthread mutex Locks Serialization Support php Revision $Revision: 308812 $ Build Date Oct 11 2011 22:55:02 Directive Local Value apc.cache_by_default On apc.canonicalize O apc.coredump_unmap Off apc.enable_cli Off apc.enabled On On apc.file_md5 Off apc.file_update_protection 2 apc.filters no value apc.gc_ttl 3600 apc.include_once_override Off apc.lazy_classes Off apc.lazy_functions Off apc.max_file_size 10M apc.mmap_file_mask /tmp/apc.bPS7rB apc.num_files_hint 1000 apc.preload_path no value apc.report_autofilter Off apc.rfc1867 Off apc.rfc1867_freq 0 apc.rfc1867_name APC_UPLOAD_PROGRESS apc.rfc1867_prefix upload_ apc.rfc1867_ttl 3600 apc.serializer default apc.shm_segments 1 apc.shm_size 256M apc.slam_defense On apc.stat Off apc.stat_ctime Off apc.ttl 7200 apc.use_request_time On apc.user_entries_hint 4096 apc.user_ttl 0 apc.write_lock On apc.php reveals the following graph, no matter how long the server runs (cache size fluctuates and hovers at just under 32MB. See image http://i.stack.imgur.com/2bwMa.png You can see that the cache is trying to allocate 256MB, but the brown piece of the pie keeps getting recycled at 32MB. This is confirmed as refreshing the apc.php page shows cached file counts that move up and down (implying that the cache is not holding onto all of its files). Does anyone have an idea of how to get APC to use more than 32 MB for its cache size?? **Note that the identical behavior occurs for eaccelerator, xcache, and APC. I read here: http://www.litespeedtech.com/support/forum/archive/index.php/t-5072.html that suEXEC could cause this problem.

  Read the article

• how to use iptables to block the IP of device connected to openwrt router

  - by scola

  I have two routers(A,B).the A connect to internet with IP:192.168.1.1 The openwrt router B connect the lan of A by bridge with static IP:192.168.1.111. I am learning to use iptables to control the devices connected to B(wlan) . I use my phone to connect wifi of B,the phone's IP is IP:192.168.1.100.it can surf the internet normally. I want to block the phone's IP to make the phone can not connect to internet. refer to http://bredsaal.dk/some-small-iptables-on-openwrt-tips iptables -A input_wan -s 192.168.1.100 --jump REJECT iptables -A forwarding_rule -d 192.168.1.100 --jump REJECT but it do not work.the phone still connect to internet normally. and I tried other chain(INPUT,OUTPUT,FORWARD).so many chains confused me. iptables -I OUTPUT -o br-lan -s 192.168.1.100 -j DROP and it do not work again. I'm sure that the iptables have no problem. root@OpenWrt:/etc# iptables -L|grep Chain Chain INPUT (policy ACCEPT) Chain FORWARD (policy DROP) Chain OUTPUT (policy ACCEPT) Chain forward (1 references) Chain forwarding_lan (1 references) Chain forwarding_rule (1 references) Chain forwarding_wan (1 references) Chain input (1 references) Chain input_lan (1 references) Chain input_rule (1 references) Chain input_wan (1 references) Chain output (1 references) root@OpenWrt:/etc# ifconfig br-lan Link encap:Ethernet HWaddr 0C:82:68:97:57:BA inet addr:192.168.1.111 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e82:68ff:fe97:57ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14976 errors:0 dropped:0 overruns:0 frame:0 TX packets:7656 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2851980 (2.7 MiB) TX bytes:1902785 (1.8 MiB) eth0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:58201 errors:0 dropped:11 overruns:0 frame:0 TX packets:45012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54591348 (52.0 MiB) TX bytes:5711142 (5.4 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:312 errors:0 dropped:0 overruns:0 frame:0 TX packets:312 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:39961 (39.0 KiB) TX bytes:39961 (39.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 0C-82-68-97-57-BA-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4900 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1223807 (1.1 MiB) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37346 errors:0 dropped:0 overruns:0 frame:0 TX packets:49662 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:3808021 (3.6 MiB) TX bytes:54486310 (51.9 MiB) root@OpenWrt:/etc/config# cat network config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'ifname' 'eth0' option 'type' 'bridge' option 'proto' 'static' option 'ipaddr' '192.168.1.111' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.1' option dns 192.168.1.1 and how to use iptables to control the network of wlan? Thanks in advance and sorry for poor English.

  Read the article

• Can gedit on mac be used to edit files over ssh?

  - by Dave

  I use a linux machine at work and a mac at home. I can ssh from my machine at home to my work machine. But the only editor that I have access to on the command line then is vi, which I don't like. Is there a way to use gedit on my mac to edit files remotely over an ssh connection? This page says that it can be done, but I think that it assumes that you are using gedit on ubuntu. On my mac (os 10.5.8) I don't have the "bookmark" option when I click "connect to server". http://thecodecentral.com/2010/04/02/use-gedit-as-remote-file-editor-via-ftp-and-ssh-ubuntu/comment-page-1#comment-50558

  Read the article

• Complete machine freezes...at a loss

  - by user28818

  Guys, We built around 12 machines a few months ago to run Ubuntu. They each have the following specs: ASUS Z8NA-D6 motherboard Dual quad core Intel(R) Xeon(R) CPU E5520 @ 2.27GHz OCZ Mod Extreme Pro 500W power supply 12 GB Kingston RAM Nvidia GeForce 9800 GT graphics card My machine ran well for awhile. However, it started experiencing random lockups. These lockups are not X lockups, they are complete system freezes. The nic stops responding, the magic sysrq buttons won't work. The machine is dead. I first suspected RAM. Memtest86 didn't find anything, but I replaced the RAM anyway. Still, lockups. So I replaced the graphics card. Still, more lockups. They became more and more frequent and started to happen 2-3 times a day. So I replaced the motherboard and power supply in one fell swoop. Suddenly, no more lockups! Woohoo! Except, a week later, in the morning, the machine wouldn't wake up. I reset it, started it up, and the log files showed the last entry at around 11 pm the evening before. This has started occurring with more frequency...now just about every morning I come in, the machine is locked up, and has been since the night before. Yesterday, in the 3 weeks since I replaced the motherboard and power supply, the machine actually locked up on in in mid-work. This is the first time since replacing the two (MB and PS) that this happened while I was using it. All others occurred while I was away. I'm at a loss. Nothing is in syslog or message that would indicate a problem around the time of the lockup. Temps are good...I use lmsensors to monitor and have a script that writes the output to file every minute. They never get that high. The only thing I haven't replaced at this point is the case and the harddrives. I doubt either could be the cause. What would you do if you were in my shoes? Is there a troubleshooting approach I'm missing? For the record, all of the other machines, all eleven of them, don't have any problems. They're all running the same version of Ubuntu (Lucid) that I am. Thanks!

  Read the article

• Clipboard feature in Windows

  - by iceman

  In Opensuse 11.0 Linux we can select any piece of text anywhere(browser, emacs..) and its in the clipboard and then we can paste it with the middle mouse click. How can i get similar functionality in Windows Xp?

  Read the article

• mod_ssl RPM conflict

  - by 0A0D

  I build Apache httpd into an RPM using these sites: http://erikwebb.net/blog/compile-and-install-apache-24-red-hat-enterprise-linux-rhel-6-or-centos-6 http://ramblin-dude.blogspot.com/2013/04/compiling-rpm-for-httpd-on-rhel-57.html I was successful at building apr* and httpd*. However, when I try to install httpd using rpm -Uvh httpd-devel-2.2.25-1.x86_64.rpm httpd-2.2.25-1.x86_64.rpm mod_ssl-2.2.25-1.x86_64.rpm I get the following error: package mod_ssl-2.2.3-82.el5_9.x86_64 (which is newer than mod_ssl-2.2.25-1.x86_64) is already installed. I have httpd 2.2.3-82 installed. Do I need to remove it first? Seems counterintuitive.

  Read the article

• Echo 404 directly from nginx to improve performance

  - by user64204

  I am in charge of production servers serving static content for a website. Those servers are constantly being crawled by bots looking for potential exploits (which isn't that much of a problem security-wise because no application can be reached behind the web server) but generates thousands of 404 per day, sometimes per hour. I am looking into ways of blocking those requests but it's tricky (you want to make sure you don't block legitimate traffic and these bots are becoming more and more clever at looking like they're legit) and is going to take me a while to find an acceptable solution. In the meantime I would like to reduce the performance impact of serving those 404 pages. Indeed we're using nginx which by default is configured to serve it's 404 page from the disk (This can be changed using the error_page directive but in the end the 404 will either have to be served from disk or from another external source (e.g. upstream application which would be worst)) which isn't ideal. I ran a test with ab on my local machine with a basic configuration: in one case I echo a message directly from nginx so the disk isn't touched at all, in the other case I hit a missing page and nginx serves its 404 from disk. server { # [...] the default nginx stuff location / { } location /this_page_exists { echo "this page was found"; } } Here are the test results (my laptop has Intel(R) Core(TM) i7-2670QM + SSD in case you're wondering why they are so high): $ ab -n 500000 -c 1000 http://localhost/this_page_exists Requests per second: 25609.16 [#/sec] (mean) $ ab -n 500000 -c 1000 http://localhost/this_page_doesnt_exists Requests per second: 22905.72 [#/sec] (mean) As you can see, returning a value with echo is 11% ((25609-22905)÷22905×100) faster than serving the 404 page from disk. Accordingly I would like to echo a simple 404 Page not Found string from nginx. I tried many things so far but they all failed, essentially the idea was this: location / { try_files $uri @not_found; } location @not_found { echo "404 - Page not found"; } The problem is that as soon as the echo directive is used, the http response code is set to 200. I tried changing that by doing error_page 200 = 400 but that breaks the configuration. How can I serve a 404 page directly from nginx? (without hacking the source which may be might next step)

  Read the article

• How to make Windows 7 use the internet connection that I specify

  - by user138957

  I have a LAN adapter and a USB wireless internet connection. When both connected windows 7 always uses the USB. I tried changing the metric values but no luck. Let me explains the steps I took. Currently automatic metric on all adapters. LAN connected. ipconfig shows that it is connected to the correct ip/dns/gateway etc. IPv4 Route table shows Metric 24 Then connected USB. ipconfig shows USB connectivity then LAN in that order. Internet is now through USB. IPv4 Route table shows Metric 4249 for LAN and USB is 41. Gateway for USB shows "on-link". netstat -rn shows USBDEVICE on top. Changed LAN metric to 5 and now the route table shows LAN as 9 (not sure why it added 4) and USB as 41. netstat shows LAN then USB. ipconfig shows LAN then USB. But still connection is through USB. How do I know? Task manager shows utilization only through USB as well as speed is showing around 1mbps rather than LANs 10mbps. How can I get win7 use LAN while USB is connected. I am just trying to use USB as a backup just in case I lose LAN connection. Please help!! I thought i will make USB metric manually to say 10. But it says I have to reconnect for it to be effective. Currently USB still shows below LAN and still has 9 and 41 in the table. Disconnected USB. Table shows LAN metric as 24 (Not sure why it got changed from 9 and setting got reverted by to automatic) Reconnected USB. Now in the setting still shows 10 and the route table shows 11 for USB and LAN shows 4249 (settings shows 4245, 4 less)) For some reason restarting USB is resetting LAN setting when reconnected. Thanks

  Read the article

• linux disk usage report inconsistancy after removing file. cpanel inaccurate disk usage report

  - by brando

  relevant software: Red Hat Enterprise Linux Server release 6.3 (Santiago) cpanel installed 11.34.0 (build 7) background and problem: I was getting a disk usage warning (via cpanel) because /var seemed to be filling up on my server. The assumption would be that there was a log file growing too large and filling up the partition. I recently removed a large log file and changed my syslog config to rotate the log files more regularly. I removed something like /var/log/somefile and edited /etc/rsyslog.conf. This is the reason I was suspicious of the disk usage report warning issued by cpanel that I was getting because it didn't seem right. This is what df was reporting for the partitions: $ [/var]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 511M 8.9G 6% / tmpfs 5.9G 0 5.9G 0% /dev/shm /dev/sda1 99M 53M 42M 56% /boot /dev/sda8 883G 384G 455G 46% /home /dev/sdb1 9.9G 151M 9.3G 2% /tmp /dev/sda3 9.9G 7.8G 1.6G 84% /usr /dev/sda5 9.9G 9.3G 108M 99% /var This is what du was reporting for /var mount point: $ [/var]# du -sh 528M . clearly something funky was going on. I had a similar kind of reporting inconsistency in the past and I restarted the server and df reporting seemed to be correct after that. I decided to reboot the server to see if the same thing would happpen. This is what df reports now: $ [~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 511M 8.9G 6% / tmpfs 5.9G 0 5.9G 0% /dev/shm /dev/sda1 99M 53M 42M 56% /boot /dev/sda8 883G 384G 455G 46% /home /dev/sdb1 9.9G 151M 9.3G 2% /tmp /dev/sda3 9.9G 7.8G 1.6G 84% /usr /dev/sda5 9.9G 697M 8.7G 8% /var This looks more like what I'd expect to get. For consistency this is what du reports for /var: $ [/var]# du -sh 638M . question: This is a nuisance. I'm not sure where the disk usage reports issued by cpanel get their info but it clearly isn't correct. How can I avoid this inaccurate reporting in the future? It seems like df reporting wrong disk usage is a strong indicator of the source problem but I'm not sure. Is there a way to 'refresh' the filesystem somehow so that the df report is accurate without restarting the server? Any other ideas for resolving this issue?

  Read the article

• What would cause my SendMail server not to acknowledge receiving a TCP Sequence?

  - by Mike B

  My TCP/IP Stack knowledge is a little rusty so please bear with me.... I have a CentOS 5.7 server with SendMail and am having seeing intermittent timeout issues sending email (particularly larger email) to other remote domains. It doesn't happen with all attachments or recipient domains. Just some. After some extended troubleshooting, I think I've narrowed it down to TCP Sequences not being acknowledged. Here's a breakdown of the TCP session from a packet capture I collected directly on my MTA (fooMTA): Packet 1 - 11: Standard TCP handshake followed by initial SMTP conversation. No errors. Packet #12 Recipient MTA: TCP sequence 231. Ack 91. Packet #13 FooMTA: TCP sequence 91. Ack 305. Packet #14 FooMTA: TCP sequence 1115. Ack 305. Packet #15 Recipient MTA: TCP sequence 305. Ack 2495. Packet #16 FooMTA: TCP sequence 2495. Ack 305. Packet #17 FooMTA: TCP sequence 5255. Ack 305. Packet #18: Recipient MTA: TCP sequence 305. Ack 5255. Packet #19: FooMTA: TCP sequence 6635. Ack 305. Packet #20: FooMTA: TCP sequence 8015. Ack 305. Packet #21: Recipient MTA: TCP Sequence 305. Ack 8015. Packet #22: FooMTA: TCP Sequence 10775. Ack 305. Packet #23: FooMTA: TCP Sequence 13535. Ack 305. Packet #24: Recipient MTA: TCP sequence 305. Ack 10775 Packet #25: FooMTA: TCP Sequence 14915. Ack 305 It keeps going like this with my server still thinking it hasn’t received sequence 305… in response the remote side eventually retransmits its prior data thinking that it never arrived. Eventually the gap gets so large that no new data is sent and the remote MTA keeps retransmitting old stuff. This contributes to an exponential backoff and eventually the remote side gives up. What’s strange to me is that I see the “missing” TCP sequence (305 in this case) arriving back to my server (via a packet capture collected directly from fooMTA) So I don’t get why my server keeps asking for it. Could this be firewall related? What would be the next step in troubleshooting?

  Read the article

• Can't ping Ip over bridge

  - by tmn29a

  I'm unable to ping another host over a bridge I created, I can't see the error -.- It's a remote machine running debian stable with some backports for which I want to set up DHCP on the new Subnet 172.30.xxx.xxx to be used for KVM-Guests. ifconfig : bond0 Link encap:Ethernet HWaddr e4:11:5b:d4:94:30 inet addr:10.54.2.84 Bcast:10.54.2.127 Mask:255.255.255.192 inet6 addr: fe80::e611:5bff:fed4:9430/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:34277 errors:0 dropped:0 overruns:0 frame:0 TX packets:18379 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2638709 (2.5 MiB) TX bytes:2887894 (2.7 MiB) br0 Link encap:Ethernet HWaddr f2:fc:4d:7f:15:f0 inet addr:172.30.254.66 Bcast:172.30.254.127 Mask:255.255.255.192 inet6 addr: fe80::f0fc:4dff:fe7f:15f0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:252 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:10800 (10.5 KiB) Pings : ping -I br0 172.30.xxx.65 PING 172.30.xxx.65 (172.30.xxx.65) from 172.30.xxx.66 br0: 56(84) bytes of data. --- 172.30.xxx.65 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2017ms ping -I bond0 172.30.254.65 PING 172.30.xxx.65 (172.30.xxx.65) from 10.54.2.84 bond0: 56(84) bytes of data. 64 bytes from 172.30.x.65: icmp_req=1 ttl=64 time=0.599 ms 64 bytes from 172.30.x.65: icmp_req=2 ttl=64 time=0.575 ms 64 bytes from 172.30.x.65: icmp_req=3 ttl=64 time=0.565 ms --- 172.30.x.65 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 0.565/0.579/0.599/0.031 ms Route : Destination Gateway Genmask Flags Metric Ref Use Iface 172.30.x.64 * 255.255.255.192 U 0 0 0 br0 10.54.x.64 * 255.255.255.192 U 0 0 0 bond0 default 10.54.x.65 0.0.0.0 UG 0 0 0 bond0 default 172.30.x.65 0.0.0.0 UG 0 0 0 br0 The Interface : cat /etc/network/interfaces auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.54.x.84 netmask 255.255.255.192 network 10.54.x.64 gateway 10.54.x.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports bond0 address 172.30.x.66 broadcast 172.30.x.127 netmask 255.255.x.192 gateway 172.30.x.65 bridge_maxwait 0 If you need more info please ask. Thanks for your help !

  Read the article

• Remote Desktop Logon on Linux from Windows Vista

  - by iamrohitbanga

  I have a PC running Opensuse 11.0 Linux. I currently login using ssh with putty. However this is a command line login. How to do a remote xserver login from windows to run a gnome or kde session. what software should I use? I have the root password for the Linux PC and admin privileges on vista.

  Read the article

• Apache certificates for some urls not working

  - by Vegaasen

  We are having a rather strange problem with a Apache-installation. Here is a short summary: Currently I'm setting up Apache with https, and server-certificates. This is fairly easy and works straight out of the box - as expected. This is the configuration for this setup: Listen 443 SSLEngine on SSLCertificateFile "/progs/apache/ssl/example-site.no.pem" SSLCertificateKeyFile "/progs/apache/ssl/example-site.no.key" SSLCACertificateFile "/progs/apache/ssl/ca/example_root.pem" SSLCADNRequestFile "/progs/apache/ssl/ca/example_intermediate.pem" SSLVerifyClient none SSLVerifyDepth 3 SSLOptions +StdEnvVars +ExportCertData RequestHeader set ssl-ClientCert-Subject-CN "%{SSL_CLIENT_S_DN}s" RewriteEngine On ProxyPreserveHost On ProxyRequests On SSLProxyEngine On ... <LocationMatch /secureStuff/$> SSLVerifyClient require Order deny,allow Allow from All </LocationMatch> ... <Proxy balancer://exBalancer> Header add Set-Cookie "EX_ROUTE=EB.%{BALANCER_WORKER_ROUTE}e; path=/" env=BALANCER_ROUTE_CHANGED BalancerMember http://10.0.0.1:7200 route=ee1 retry=300 flushpackets=off keepalive=on BalancerMember http://10.0.0.2:7200 route=ee2 retry=300 flushpackets=off keepalive=on status=+H ProxySet stickysession=EX_ROUTE scolonpathdelim=Off timeout=10 nofailover=off failonstatus=505 maxattempts=1 lbmethod=bybusyness Order deny,allow Allow from all </Proxy> RewriteCond %{REQUEST_URI} !^/index.html [NC] RewriteRule ^/(.*)$ balancer://exBalancer/$1 [P,NC] ProxyPassReverse / balancer://exBalancer/ Header edit Set-Cookie "(.*)" "$1;HttpsOnly" ... So - everything works fine and as expected for all of the pages that are not a part of the LocationMatch-directive. When requesting something that matches the LocationMatch-directive, I'm asked for a certificate (hence the SSLVerifyClient required attribute) - and getting all the correct certificates in my browser that is based on the root/intermediate chain. After choosing a certificate and clicking "OK", this is what pops up in the apache logs: [ssl:info] [pid 9530:tid 25] [client :43357] AH01998: Connection closed to child 86 with abortive shutdown ( [Thu Oct 11 09:27:36.221876 2012] [ssl:debug] [pid 9530:tid 25] ssl_engine_io.c(1171): (70014)End of file found: [client 10.235.128.55:45846] AH02007: SSL handshake interrupted by system [Hint: Stop button pressed in browser?!] And this just spams the logs. What is happening here? I can see this configuration working on my local machine, but not on one of our servers. There is no configration differences between the servers, only minor application-wise-changes. I've tried the following: 1) Removing CA-certificate-checking (works) 2) Adding required CA-certificate for the whole site (works) 3) Adding "SSLVerifyClient optional" does not work 4) ++ Server/Application Information Local: -OpenSSL v.1.0.1x -Apache 2.4.3 -Ubuntu -mpm: event -every configuration should be turned on (failing) server: -OpenSSL 0.9.8e -Apache 2.4.2 -SunOS -mpm: worker -every configuration should be turned on Please let me know if more information is needed, I'll provide it instantly. Brief sum-up: -Running apache 2.4 -Server certificates works just fine -Client certificates for some /Locations does not work, fails with errors PS: Could it be related with the OpenSSL version and the "Renegotiation" stuff related to TLS/SSLv3?

  Read the article

• Troubleshooting Network Speeds -- The Age Old Inquiry

  - by John K

  I'm looking for help with what I'm sure is an age old question. I've found myself in a situation of yearning to understand network throughput more clearly, but I can't seem to find information that makes it "click" We have a few servers distributed geographically, running various versions of Windows. Assuming we always use one host (a desktop) as the source, when copying data from that host to other servers across the country, we see a high variance in speed. In some cases, we can copy data at 12MB/s consistently, in others, we're seeing 0.8 MB/s. It should be noted, after testing 8 destinations, we always seem to be at either 0.6-0.8MB/s or 11-12 MB/s. In the building we're primarily concerned with, we have an OC-3 connection to our ISP. I know there are a lot of variables at play, but I guess I was hoping the experts here could help answer a few basic questions to help bolster my understanding. 1.) For older machines, running Windows XP, server 2003, etc, with a 100Mbps Ethernet card and 72 ms typical latency, does 0.8 MB/s sound at all reasonable? Or do you think that slow enough to indicate a problem? 2.) The classic "mathematical fastest speed" of "throughput = TCP window / latency," is, in our case, calculated to 0.8 MB/s (64Kb / 72 ms). My understanding is that is an upper bounds; that you would never expect to reach (due to overhead) let alone surpass that speed. In some cases though, we're seeing speeds of 12.3 MB/s. There are Steelhead accelerators scattered around the network, could those account for such a higher transfer rate? 3.) It's been suggested that the use SMB vs. SMB2 could explain the differences in speed. Indeed, as expected, packet captures show both being used depending on the OS versions in play, as we would expect. I understand what determines SMB2 being used or not, but I'm curious to know what kind of performance gain you can expect with SMB2. My problem simply seems to be a lack of experience, and more importantly, perspective, in terms of what are and are not reasonable network speeds. Could anyone help impart come context/perspective?

  Read the article

• Local dns for testing websites using mobile devices

  - by Morpheu5

  Hi. I have no idea where to start from so sorry in advance if this topic has already been discussed. I usually develop web sites using my laptop as a development server, and recently I needed to test a web site using various mobile devices that can connect via wifi. Having no real AP, I set up a ad-hoc network using my laptop's wireless card and the devices can correctly browse the Internet and access the laptop's web server. The setup is as follows: subnet: 192.168.1.0/24 gateway to the Internet (wired adsl router/modem): 192.168.1.1 laptop: 192.168.1.64 (eth0, wired if connected to the gateway) and 192.168.1.32 (eth1, wifi if somewhat bridged to eth0) mobile devices (same for all, I only use one of them at any time for simplicity): 192.168.1.11 with default gw 192.168.1.1 Now, if I open either 192.168.1.32 or 192.168.1.64 from the mobile devices, I correctly get the default host of my Apache configuration. However I usually work with virtual hosts for many practical reasons, one of which being Drupal's peculiar implementation of multi-sites. For those who don't know how this works, Drupal takes the request's hostname and searches into its sites/ subdirectories for an appropriate configuration file. So, for example, suppose I request www.example.com, then Drupal would search for a config file in the following directories: sites/www.example.com/ sites/example.com/ sites/com/ sites/default/ So I decided to adopt the following style of virtual hosts: if the website I'm working on will be accessible using www.example.com I set up a sites/www.example.com/ directory and create a virtual host for local.www.example.com so Drupal have no trouble finding it. I've been told this is suboptimal from a dns point of view since I'd have to create an authoritative entry for example.com and turn Bind on only when I'm supposed to access the local copy, which is weird. However, if this is the only path I can follow, I still have some problems with Bind's configuration, as I couldn't find any guide that tells me in a clear, noob-friendly way, how to set up such an entry. On the other hand, I was wondering if I could set up an authoritative entry for local, so I could access www.example.com.local and tell in some way (which I don't even know if this is possible) Apache to put www.example.com instead of www.example.com.local in the relevant environment variable. Anyway, I have a last problem, sort of: when I launch Bind in debug mode with high verbosity, and make 192.168.1.32 as the primary dns for the devices, the output doesn't say anything about requests being made from the devices to Bind, so I'm not even sure it comes into play. As you can see, I'm a complete noob at these matters, but I'm eager to learn, so any help/pointer will be appreciated.

  Read the article

• how can I give openvpn clients access to a dns server (bind9) that is located on the same machine as the openvpn server

  - by lacrosse1991

  I currently have a debian server that is running an openvpn server. I also have a dns server (bind9) that I would like give allow access to by the connected openvpn clients, but I am unsure as of how to do this, I already known how to send dns options to the clients using push "dhcp-option DNS x.x.x.x" but I am just unsure how give the clients access to the dns server that is located on the same machine as the vpn server, so if anyone could point me in the right direction I would really appreciate it. Also in case this would have anything to do with adding rules to iptables, this is my current configuration for iptables # Generated by iptables-save v1.4.14 on Thu Oct 18 22:05:33 2012 *nat :PREROUTING ACCEPT [3831842:462225238] :INPUT ACCEPT [3820049:461550908] :OUTPUT ACCEPT [1885011:139487044] :POSTROUTING ACCEPT [1883834:139415168] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE COMMIT # Completed on Thu Oct 18 22:05:33 2012 # Generated by iptables-save v1.4.14 on Thu Oct 18 22:05:33 2012 *filter :INPUT ACCEPT [45799:10669929] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [45747:10335026] :fail2ban-apache - [0:0] :fail2ban-apache-myadmin - [0:0] :fail2ban-apache-noscript - [0:0] :fail2ban-ssh - [0:0] :fail2ban-ssh-ddos - [0:0] :fail2ban-webserver-w00tw00t - [0:0] -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache-myadmin -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-webserver-w00tw00t -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache-noscript -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh-ddos -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh -A INPUT -i tun+ -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 3306 -j ACCEPT -A FORWARD -i tun+ -j ACCEPT -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT -A fail2ban-apache -j RETURN -A fail2ban-apache-myadmin -s 211.154.213.122/32 -j DROP -A fail2ban-apache-myadmin -s 201.170.229.96/32 -j DROP -A fail2ban-apache-myadmin -j RETURN -A fail2ban-apache-noscript -j RETURN -A fail2ban-ssh -s 76.9.59.66/32 -j DROP -A fail2ban-ssh -s 64.13.220.73/32 -j DROP -A fail2ban-ssh -s 203.69.139.179/32 -j DROP -A fail2ban-ssh -s 173.10.11.146/32 -j DROP -A fail2ban-ssh -j RETURN -A fail2ban-ssh-ddos -j RETURN -A fail2ban-webserver-w00tw00t -s 217.70.51.154/32 -j DROP -A fail2ban-webserver-w00tw00t -s 86.35.242.58/32 -j DROP -A fail2ban-webserver-w00tw00t -j RETURN COMMIT # Completed on Thu Oct 18 22:05:33 2012 also here is my openvpn server configuration port 1194 proto udp dev tun ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt keepalive 10 120 comp-lzo user nobody group users persist-key persist-tun status /var/log/openvpn/openvpn-status.log verb 3 push "redirect-gateway def1" push "dhcp-option DNS 213.133.98.98" push "dhcp-option DNS 213.133.99.99" push "dhcp-option DNS 213.133.100.100" client-to-client

  Read the article

• Cloud storage provider lost my data. How to back up next time?

  - by tomcam

  What do you do when cloud storage fails you? First, some background. A popular cloud storage provider (rhymes with Booger Link) damaged a bunch of my data. Getting it back was an uphill battle with all the usual accusations that it was my fault, etc. Finally I got the data back. Yes, I can back this up with evidence. Idiotically, I stayed with them, so I totally get that the rest of this is on me. The problem had been with a shared folder that works with all 12 computers my business and family use with the service. We'll call that folder the Tragic Briefcase. It is a sort of global folder that's publicly visible to all computers on the service. It's our main repository. Today I decided to deal with some residual effects of the Crash of '11. Part of the damage they did was that in just one of my computers (my primary, of course) all the documents in the Tragic Briefcase were duplicated in the Windows My Documents folder. I finally started deleting them. But guess what. Though they appeared to be duplicated in the file system, removing them from My Documents on the primary PC caused them to disappear from the Tragic Briefcase too. They efficiently disappeared from all the other computers' Tragic Briefcases as well. So now, 21 gigs of files are gone, and of course I don't know which ones. I want to avoid this in the future. Apart from using a different storage provider, the bigger picture is this: how do I back up my cloud data? A complete backup every week or so from web to local storage would cause me to exceed my ISP's bandwidth. Do I need to back up each of my 12 PCs locally? I do use Backupify for my primary Google Docs, but I have been storing taxes, confidential documents, Photoshop source, video source files, and so on using the web service. So it's a lot of data, but I need to keep it safe. Backup locally would also mean 2 backup drives or some kind of RAID per PC, right, because you can't trust a single point of failure? Assuming I move to DropBox or something of its ilk, what is the best way to make sure that if the next cloud storage provider messes up I can restore?

  Read the article

• Bringing the xenbr0 interface up on XEN under Ubuntu 8.04

  - by iyl

  I installed XEN on Ubuntu 8.04 using this tutorial: http://www.howtoforge.com/ubuntu-8.04-server-install-xen-from-ubuntu-repositories but after I reboot with the XEN kernel, I don't have xenbr0 device. I see that network-bridge script runs and it creates peth0 device, but not xenbr0. I have a very basic IP setup, with a single static IP defined in /etc/network/interfaces. The only unusual thing is that my hosting (1&1) gave me a netmask 255.255.255.255, so I had to add the default gateway with this script: /sbin/route add -host 10.255.255.1 dev eth0 /sbin/route add default gw 10.255.255.1 Everything else is plain vanilla Ubuntu 8.04.

  Read the article

• Trobleshooting input device detection in Windows Xp Pro Sp3

  - by iceman

  My laptop (Acer travelmate 4152NlCi)doesn't respond to the keyboard and mouse anymore while booting in Windows Xp Pro Sp3. i can't type the password and login. I have Opensuse 11.0 on it as well and it works. So I can boot into Linux and not Windows, not even in safe mode. What would be the troubleshooting steps?

  Read the article

• Incremental RPM package version "numbers" for x.y.z > x.y.z-beta (or alpha, rc, etc)

  - by Jonathan Clarke

  In order to publish RPM packages of several different versions of some software, I'm looking for a way to specify version "numbers" that are considered "upgrades", and include the differentiation of several pre-release versions, such as (in order): "2.4.0 alpha 1", "2.4.0 alpha 2", "2.4.0 alpha 3", "2.4.0 beta 1", "2.4.0 beta 2", "2.4.0 release candidate", "2.4.0 final", "2.4.1", "2.4.2", etc. The main issue I have with this is that RPM considers that "2.4.0" comes earlier than "2.4.0.alpha1", so I can't just add the suffix on the end of the final version number. I could try "2.4.0.alpha1", "2.4.0.beta1", "2.4.0.final", which would work, except for the "release candidate" that would be considered later than "2.4.0.final". An alternative I considered is using the "epoch:" section of the RPM version number (the epoch: prefix is considered before the main version number so that "1:2.4.0" is actually earlier than "2:1.0.0"). By putting a timestamp in the epoch: field, all the versions get ordered as expected by RPM, because their versions appear to increment in time. However, this fails when new releases are made on several major versions at the same time (for example, 2.3.2 is released after 2.4.0, but their version for RPM are "20121003:2.3.2" and "20120928:2.4.0" and systems on 2.3.2 can't get "upgraded" to 2.4.0, because rpm sees it as an older version). In this case, yum/zypper/etc refuse to upgrade to 2.4.0, thus my problem. What version numbers can I use to achieve this, and make sure that RPM always considers the version numbers to be in order. Or if not version numbers, other mechanism in RPM packaging? Note 1: I would like to keep the "Release:" field of the spec file for it's original purpose (several releases of packages, including packaging changes, for the same version of the packaged software). Note 2: This should work on current production versions of major distributions, such as RHEL/CentOS 6 and SLES 11. But I'm interested in solutions that don't, too, so long as they don't involve recompiling rpm! Note 3: On Debian-like systems, dpkg uses a special component in the version number which is the "~" (tilde) character. This causes dpkg to count the suffix as "negative" ordering, so that "2.4.0~anything" will come before "2.4.0". Then, normal ordering applies after the "~", so "2.4.0~alpha1" comes before "2.4.0~beta1" because "alpha" comes before "beta" alphabetically. I'm not necessarily looking to use the same scheme for RPM packages (I'm pretty sure no such equivalent exists), so this is just FYI.

  Read the article

• Wifi network stopped being visible (and usable) (Linksys wag320n)

  - by s427

  Basically, my wifi network simply stopped working for no apparent reason. It doesn't appear in the list of the available networks anymore. I can see all my neighbors' networks, but not mine. It's as if it doesn't exist anymore. The internet connection (non-wifi), which goes through the same modem/router, is fine though. I already had a similar problem about one year ago (see here: Wifi network SSID not visible ), just after buying this very modem. I finally got it to work after performing two factory resets and getting rid of the Cisco "Magic" software; but this time it's not working. I use a linksys router-modem (WAG320N) which is directly connected (via network cable) to my desktop computer (Windows 7). I have (mainly) two devices that use the wifi network: my phone (Samsung Galaxy Nexus) and an Asus tablet (TF201, aka Transformer Prime). I also resurrected an old laptop computer (Dell, running Windows XP) to test that, and it doesn't see anything either (apart from the 20 other wifi networks, of course ^^). This wifi network was working just fine and has been for about a year. I haven't touched the modem settings so I have no idea what's causing the problem. I tried: making my phone "forget" about my network, hoping it would see it again after that: no luck. re-entering the network informations (SSID/password) manually on my phone: still no luck (says it's not in range) exporting the modem configuration, resetting the modem (factory reset, via modem admin), restarting it, importing the configuration: nope. factory reset, turning it off for 15 minutes, restarting, re-factory reset, and entering the configuration manually: still nothing. Has anybody experienced something similar before? Have you any suggestion to fix that? Thanks in advance. PS: to clear things up, here are the settings of my modem regarding wifi: Basic wireless settings: Configuration: manual Radio Band: 2.4GHz Wireless Network Mode: B/G/N-Mixed SSID: s427 Channel Bandwidth: Wide - 40 MHz Channel Wide Channel: 9 - 2.452GHz Standard Channel: 11 - 2.462GHz SSID Broadcast: Enable Advanced Wireless Settings AP Isolation: Disable Authentication Type: Auto Basic Rate: Default Transmission Rate: Auto N Transmission Rate: Auto CTS Protection Mode: Disable Beacon Interval: 100 DTIM Interval: 1 Fragmentation Threshold: 2346 RTS Threshold: 2346

  Read the article

• Asterisk Dial() - passing URL to softphone

  - by Giuc

  According to https://wiki.asterisk.org/wiki/display/AST/Asterisk+11+Application_Dial the Dial() application is capable of sending an URL to the extension being called. I suppose there are softphones implementing this, maybe popping up a browser pointing to the given URL - perfect to open up automatically a CRM customer page when receiving a call by identifying his caller id. Do you know of any softphone implementing this functionality?

  Read the article

< Previous Page | 438 439 440 441 442 443 444 445 446 447 448 449  | Next Page >